-
ACC2-2 Autochange Controller Unit
$2,845.00The ACC2-2 handles the communications to and from the CMM controller, controls the ACR1 Autochange rack and multiplexes and interfaces the head and datum probe signals.
Data transmission Serial RS232, Parallel IEEE
User definable parameters
Serial: Baud Rate 300 – 19200
Parallel: address, parallel poll bitVoltage range: 85 – 264v 50/60 Hz Automatic selection
Weight (g) 3.85
Length (mm) 220
Height (mm) 88
Width (mm) 289.3 -
AC2 PC Interface Card
$2,588.00 -
AM2 Adjustment Module
$750.00 -
AM1 Adjustment Module
$750.00 -
HCU-1 Hand Control Unit
$737.00A hand held, manual head drive unit for use with PHC10-2 and PHC50 motorised head controllers. It allows an operator to manually change the orientation of the head without the need for sending commands through the CMM controller. This is invaluable when:
- programming an inspection routine (through teach cycle programming),
- utilising operator controlled “manual” inspection methods.
Features:
- A and B axis current position display
- A and B axis move direction buttons
- 2 speed action (jog and rapid move)
- Transmit button for teach cycle programming
- Status and error LED
-
PHC10-2 Probe Head Control – IEEE
$2,961.00The PHC10-2 controls any one of the PH10T, PH10M or PH10MQ heads based on commands recieved from either the CMM controller or the HCU1 (if fitted). In addition to this, the PHC10-2 interrogates the head and reports back:
- the heads A and B positions,
- any problems found
The PHC10-2 does not process any of the probe sensor signals. These are railed clean
through through the heads axes and controller to the probe interface.Data transmission RS232 or IEEE
User definable parameters
- Serial Baud rate 300 – 19200 parallel address, parallel poll bit
- Current Consumption: (at 240V) less than 500mA
- Voltage range: 85-264V 47/66Hz automatic selection
- Input connectors: 15 way ‘D’
- Probe output connectors: 7 pin DIN or 9 way ‘D’ type
- Mounting: rack mounted or stand alone
- Hand control unit: HCU1 only
Weight (g) 2860
Length (mm) 220
Height (mm) 88
Width (mm) 289.3 -
PHC10-2 Probe Head Control – RS232
$2,852.00The PHC10-2 controls any one of the PH10T, PH10M or PH10MQ heads based on commands received from either the CMM controller or the HCU1 (if fitted). In addition to this, the PHC10-2 interrogates the head and reports back:
- the heads A and B positions,
- any problems found
The PHC10-2 does not process any of the probe sensor signals. These are railed clean
through through the heads axes and controller to the probe interface.Data transmission RS232 or IEEE
User definable parameters
- Seria:l Baud rate 300 – 19200 parallel address, parallel poll bit
- Current Consumption: (at 240V) less than 500mA
- Voltage range: 85-264V 47/66Hz automatic selection
- Input connectors: 15 way ‘D’
- Probe output connectors: 7 pin DIN or 9 way ‘D’ type
- Mounting: rack mounted or stand alone
- Hand control unit: HCU1 only
Weight (g) 2860
Length (mm) 220
Height (mm) 88
Width (mm) 289.3
- Call Us Toll-Free: (800) 648-6944
Copyright © 2016 CMM Technology, All Rights Reserved - Powered By Stark Logic.
Terms of Use
|
Privacy Policy